Call Us
Contact Us

Surface Testing Equipment

Elcometer 123 Surface Profile Gauge

Elcometer 123 Surface Profile Gauge

Approx. Rs 18,000 / Piece


Elcometer 123 Surface Profile Gauge is easy to use gauge measures the peak-to-valley height of a blast cleaned surface.

The average of a series of measurements provides an indication of the surface roughness and allows the surfaces to be compared as blasting proceeds. This is Metric and Imperial version. Elcometer is a trademark of Elcometer Ltd., UK, registered in the UK and other countries.


Technical Specification:
Part NumberDescription
E123A--M-Elcometer 123 Surface Profile Gauge, Metric Version
E123A--E-Elcometer 123 Surface Profile Gauge, Imperial Version
Certificate AvailableCertificate of Calibration: issued for Fixed Calibration equipment and shows readings and traceability.
Accredited Certificate: can be issued for Fixed Calibration Equipment and a full UKAS traceable certificate is issued from an independent Calibration Laboratory.
Packing ListElcometer 123 Surface Profile Gauge, glass slide, 2mm Allen key, carry case and operating instrument

SCM Meter Salt Contamination Elcometer

SCM Meter Salt Contamination Elcometer

Approx. Rs 4 Lakh / Piece


SCM Meter Salt Contamination Elcometer

Being an industry leader, we offer a unique range of Scm meter salt contamination elcometer, which is 130 SCM400 salt contamination meter. The soluble salts are wrapped up in a special filter paper soaked with distilled water. Our range of product helps in measuring the conductivity of wet paper, measure the level of the salt and display the result on ugcm-2. Following are the various specification of our product.

 

Shot Grit Blasting Comparator

Shot Grit Blasting Comparator

Approx. Rs 8,900 / Piece


Shot And Grit-blasting Comparators

These two comparators are specially designed to check the roughness of steel surfaces which have been blast cleaned to cleanliness grades sa 2. 5 and sa 3 before painting. They conform to iso 850.

Additional Information:

Surface Comparator Elcometer

Surface Comparator Elcometer

Approx. Rs 4,000 / Piece


Our expert team assists us in offering a diverse range of surface comparator elcometer that is elcometer 125 surface comparator. It permits the estimation of surface roughness by both sight and touch. These are available in both shot and grit metric units only. In order to use it effective and proper preparation of surface even before coating is important. Make sure that the accurate profile or roughness has been generated. In case if the profile is too low it will reduce the coating to the surface on the other hand if the profile is too high then there will be danger that even leads to uncoated profile peak allowing rust spots to occur.

Available in both grit and shot
Metric units only


Surface Profile
The proper and effective preparation of a surface prior to coating is essential. Making sure that the correct roughness – or profile – has been generated is essential.

If the profile is too low, the adhesion of the coating to the surface will be reduced. Too high and there is the danger that the profile peaks will remain uncoated – allowing rust spots to occur.
.

Surface Profile Gauge Elcometer

Surface Profile Gauge Elcometer

Approx. Rs 3,500 / Piece


We are a known for offering a qualitative range of surface profile gauge elcometer that is elcometer 223 digital surface profile gauge. This is operated with a battery easily and is used to measure the peak-to-valley height of a surface almost like Elcometer123 analogue equivalent apart from one difference such as added benefit of direct RS232 output.

Testex Replica Tape (Press-O-Film Tape)

Testex Replica Tape (Press-O-Film Tape)

Approx. Rs 2,650 / Piece


Testex Press-O-Film Replica Tape

Press-O-Film (POF) consists of a layer of crushable plastic microfoam coated onto a polyester film of highly uniform thickness.

When compressed against a roughened material, Press-O-Film accurately replicates details of its surface roughness.

The impression can be studied in several ways:

Testex Tape is popularly called as Press-O-Film. Press-O-Film provides surface profile of a basted cleaned surface. It can produce virtually exact replicas of the blasted surface profile, which can be measured, using a snap gauge. Testex offers a simple and very accurate method of measuring blasted profiles. Press-O-Film consists of layer of crushable plastic micro foam coated onto a polyester film of highly uniform thickness. Using surface profile gauge or testex tape can test surface roughness. Most commonly used testex tape as it can give permanent record of the surfaces. Place the Testex Tape (Press-O-Film) firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the snap gauge. Testing & Inspection can be done in three easy steps. Detailed procedure is furnished with testex kit or tapes. Testex Tape is supplied in a roll containing 50 tests and is available in four different grades to cater for different applications. The snap gauge is supplied in a carrying case with a burnishing tool. Paint applicators, inspectors and researchers for its simple operations and results prefers to use Testex tapes (Press-O-Film) Testex Tape (Press-o-film) complies with ASTM, NACE and SSPC methods measurement. ASTM- Reproducibility is given in ASTM Standard 4417-93 for both "X-coarse" and "coarse" grade replica tape. NACE- Standard RP0287-95 addresses the issue of accuracy of measurement, test results. SSPC- The Society for Protective Coatings, recommends a minimum of three measurements of profile per 100 square feet (10 square meters). ISO- International Organization for Standards- Draft Standard ISO8503-5 describes preparation of steel substrates before application of paint and related products. Testex kit comprises two rolls Press-O-Film (X Coarse supplied as standard, specify different grade if required), snap gauge and burnishing tool.


Additional Information:

Testex Tape / Press-O-Film

Testex Tape / Press-O-Film

Approx. Rs 2,600 / Roll


Testex Tape / Press-O-Film USA

Testex Tape is popularly called as Press-O-Film. Press-O-Film provides surface profile of a basted cleaned surface. It can produce virtually exact replicas of the blasted surface profile, which can be measured, using a snap gauge. Testex tapes offers a simple and very accurate method of measuring blasted profiles of surface.

Testex Tape / Press O Film consists of layer of crushable plastic microfoam coated onto a polyster film of highly uniform thickness.

Surface profile gauge or testex tapes can test surface roughness. Most commonly used testex tapes / press o films are popular as it can give permanent record of the surfaces.

Place the Testex Tape (Press-O-Film) firmly on the blasted surface, apply moderate pressure with the burnishing tool, the replica has now been taken and can be measured using the snap gauge. Testing & Inspection can be done in three easy steps. Detailed procedure is furnished with testex kit or tapes.

Testex Tape is supplied in a roll containing 50 tests and is available in four different grades to cater for different applications. The snap gauge is supplied in a carrying case with a burnishing tool.

Paint applicators, inspectors and researchers for its simple operations and results prefers to use Testex tapes (Press-O-Film)

Testex Tape (Press-o-film) complies with ASTM, NACE and SSPC methods measurement.

ASTM- Reproducibility is given in ASTM Standard 4417-93 for both “X-coarse” and “coarse” grade replica tape.

NACE- Standard RP0287-95 addresses the issue of accuracy of measurement, test results.

SSPC- The Society for Protective Coatings, recommends a minimum of three measurements of profile per 100 square feet (10 square meters).

ISO- International Organization for Standards- Draft Standard ISO8503-5 describes preparation of steel substrates before application of paint and related products.

WFT Combs Elcometer

WFT Combs Elcometer

Approx. Rs 1,950 / Piece


Our company offers a wide range of WFT combs elcometer that is 112 & 3236 hexagonal wet film combs is made from high quality stainless steel to ensure its long service life, durability and reusable. These are highly suitable for measuring thickness of coatings up to 3000µm (120mils) range.

 

How to use a wet film comb

 

Furthermore, in order to use this wet film comb you first need to place a comb perpendicular that to touching the substrate. Wait for few seconds while holding the comb in position until the teeth are wet. Now take away the comb from the film. Finally the thickness of the wet film lies between the biggest wet tooth and value coated and dry tooth value or the smallest value uncoated.

Wet Film Combs WFT Gauge

Wet Film Combs WFT Gauge

Approx. Rs 1,950 / Piece


Product Description

These hexagonal precision formed stainless steel wet film combs are long lasting and reusable and are supplied in a range of thicknesses measuring up to 3000µm (120mils).

These six sided combs vary in size, giving either 24 or 36 measurement steps, depending on the comb, providing increased accuracy.

 

Using a wet film comb

Place a comb perpendicular to and touching the substrate. Hold the comb in position and wait a few seconds until the teeth are wet. Remove the comb from the film. The wet film thickness lies between the biggest value ‘coated’ or ‘wet’ tooth and the smallest value ‘uncoated’ or ‘dry’ tooth.

 

art NumberRange
Values
K0003236M20120 - 370µm20, 30, 40, 50, 60, 70, 80, 90, 100, 110, 120, 130, 150, 170, 190, 210, 230, 250, 270, 290, 310, 330, 350, 370µm
K0003236M20225 - 2000µm25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 950, 1000, 1100, 1200, 1300, 1400, 1500, 1600, 1700, 1800, 1900, 2000µm
B112----1B25 - 3000µm25, 50, 75, 100, 125, 150, 175, 200, 225, 250, 275, 300, 350, 400, 450, 500, 550, 600, 650, 700, 750, 800, 850, 900, 1000, 1100, 1200, 1400, 1600, 1800, 2000, 2200, 2400, 2600, 2800, 3000µm
K0US3236M2030.5 - 15mils0.5, 0.75, 1.0, 1.25, 1.5, 2, 2.5, 3, 3.5, 4, 4.5, 5, 5.5, 6, 6.5, 7, 8, 9, 10, 11, 12, 13, 14, 15mils
K0US3236M2041 - 80mils1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 42, 44, 46, 48, 50, 55, 60, 65, 70, 75, 80mils
B112----2B1 - 120mils1, 2, 3, 4, 5, 6, 7, 8, 9, 10, 11, 12, 14, 16, 18, 20, 22, 24, 26, 28, 30, 32, 34, 36, 38, 40, 45, 50, 55, 60, 70, 80, 90, 100, 110, 120mils
Dimensions and Weight

Elcometer 3236M201/M203

53 x 50 x 1mm (2.09 x 1.97 x 0.04”), 10g (0.35oz)
Elcometer 3236M202/M20477 x 90 x 1mm (2.95 x 3.54 x 0.04”), 22g (0.77oz)
Elcometer 11275 x 65 x 1mm (2.95 x 2.54 x 0.04”), 20g (0.7oz)
X
Provide Us More Details
Is this Requirement:

One Time Regular

How soon do you want this:

Immediate After 1 month

Purpose of Requirement:

Reselling End Use Raw Material

X

Looking for Surface Testing Equipment ?

country-ico

We will contact you soon !

Taher S

(Director)

Bombay Tools Center Bombay Pvt Ltd

Mumbai, Maharashtra, India

More Categories

View All Categories »
+91-8071683038
Contact Us