Paint & Surface Testing Insturmenst

Elektrophysik Mikrotest 5 Thickness Gauge

Approx Price: Rs 39,000 / Piece 
MikroTest 5 & 6

Applications

Non-destructive measurement of:


  • non-magnetic coatings, e.g. phosphate, paint, plastic on steel
  • nickel on steel

 

Performance features

  • Non-wearing permanent magnet
  • Measuring without power supply
  • No calibration required
  • Measurement at any angle
  • High accuracy
  • Measurement of coatings up to 20 mm

 

Models

  • MikroTest 5
    For precise and quick coating thickness measurement
  • MikroTest 6
    Fully automatic measurement without power supply

 

Measuring principle

Magnetic attraction principle

 


Analogue Surface Profile Gauge

Approx Price: Rs 4,850 / Piece 
Analogue Surface Profile Gauge

The Analog Surface Profile Gauge will allow the peak to valley height of blast-cleaned surfaces to be accurately measured in accordance with the ASTM D-4417 Method B standard. The gauge is important tool in assessment of degree surface preparation or surface cleanliness before painting.

The gauge is initially set to zero with the glass zero plate. The needle touches the glass plate and the foot is then placed on the blasted profile. The foot sits on top of the peaks and the sharp stylus travels to the bottom of the valley, allowing the gauge to display the peak to valley height. A number of measurements can be made and the average taken.

In addition the gauge can also be used to measure the effects of corrosion, i.e. pitting and cavity depth etc.

Supplied in Carrying Case with Glass Zero Plate.

Ford Cup - Viscosity Measuring Cup SS

Approx Price: Rs 5,152 / Piece 
Ford viscosity cup is a simple gravity device that permits the timed flow of a known volume of liquid passing through an orifice located at the bottom.

Under ideal conditions, this rate of flow would be proportional to the kinematic viscosity (expressed in stokes and centistokes) that is dependent upon the specific gravity of the draining liquid.However, the conditions in a simple flow cup are seldom ideal for making true measurements of viscosity.

It is important when using a Ford Cup and when retesting liquids that the temperature of the cup and the liquid is maintained, as ambient temperature makes a significant difference to viscosity and thus flow rate.

These new Ford viscosity cups are extremely easy to use. Simply pour your sample into the cup and measure the time it takes for the liquid to flow through the orifice until the first break in the liquid stream. Use the included table to convert the elapsed time to centistokes (cSt).

The cups are made from solid SS; the orifice is made from SS All the cups are calibrated to NIST-traceable oils.
An accessory kit, a stand, and a stand with water bath ports are sold separately.

Paint / Coating Thickness Tester

Approx Price: Rs 28,045 / Piece 
Paint / Coating Thickness Tester

We Offer latest digital pocket paint thickness gauge.

Can be operated by unskilled workers with single keypad operation and automatic switch off when no reading is being taken.

Paint thickness tester for all types of application to measure thickness of paint, epoxy, powder coating, foil film, thin panel sheets, paper, automotive, car painting booths and repair shop etc. It works on non destructive principle.

The digital electronic gauge measures thickness on steel including body panels, engine components, and wheels has measuring range measures range up to 1500 µ and accuracy of up to ±2µm / 2%.

is a pocket size tester, which also enables checking the condition of motor car body paint and determining thickness of the painted surface. Enables to check weather the car was painted for the second time or the body was repaired. Makes possible finding places where filler was laid and how thick it was done. Help to reduce expensive paint materials and improve finish consistency and quality. Highly useful tester for insurance survey, automobile & ancillary manufactures.


Mechanical gauges, spring operated gauges are working on the magnetic permeability and based on residual magnetism in steel have lower accuracy of up to + 5%. In view of above, Elmetron MG 105 digital pocket sized tester is now best option in the industry compared to analog instruments.

Suitable for paint manufacturer, painting inspector, painter, sand blasting contractors, finishing, anti- corrosion painting contractors, machine tools manufacturers, car insurance surveyors, automobile industries, can manufacturers, automobile repair, quality control departments, pipeline industry, aeronautical industry, thin film sheets packaging industry manufacturers, gas & water industries, and auto service stations.

Coatem is a digital paint thickness tester Instrument has measuring range upto 1500 microns with resolution of 1 micron and accuracy ±2µm / 2%, weight 150 gms., Compact size, auto shut-off and operated on batteries.

We also offer instruments for most of the applications covering full range of thickness of powder coating / painting / finishing industries with steel, copper, nickel, aluminum, and other bases.

Selection of gauge can be decided based on the substrate and type of coating. Choices of various instruments / models are given below for selecting the correct gauge.

Digital Coating Thickness Gauge Elco Test

Approx Price: Rs 100 / Piece 

Digital Coating Thickness Gauge – ElcoTest ®

Our new high specification Coating thickness Gauge is the ultimate tool for measuring the thickness of paint, the thickness of coatings and the thickness of powder coatings on all types of metal substrates in the field of coatings inspection equipment and supply a range of quality inspection equipment.

The gauge will measure coatings on ferrous (iron, steel) and non-ferrous substrates (aluminium). The gauge will sense the substrate under the coating and will switch automatically to the ferrous or non-ferrous measurement setting.

 

The gauge can be easily switched to measure and display readings in either in metric or imperial units of measurement.

The gauge has a “flip” function that allows the user to turn the gauge through 180 degrees so that it can be used upside down for ease of reading at different angles.

Features

ü Simple switch between mils or microns

ü Factory calibrated and ready to use straight out of the box

ü Large LCD flip-display making it easy to read in any position

ü Accurate readout in just 1 second

ü Memory will record the last 10 measurements

ü Auto on/off – Switches off after 30 seconds if not used within that time period saving battery life

ü Auto measurement - simply place on the surface to be measured

ü Auto detection and display of substrate type (Ferromagnetic or non-Ferromagnetic base)

ü Can be switched between Metric and Imperial measurement units (µm/mil)

ü Extremely portable, lightweight and supplied in rugged hard case for the ultimate protection

ü Supplied with pull off screen protector

Specifications:

Measurement Range:

0 to 50 mil or 0 to 1250 µm (microns)

Accuracy:

± (0.1 mils + 3%) or ± (2 µm + 3%)

Resolution:

1µm or 0.1mil

Memory:

10 Readings

Packed Weight:

0.52 Kg

Packed Dimensions:

160 x 72 x 42 mm

Gauge Weight:

0.15 Kg

Gauge Size:

110 x 45 x 30 mm


Standard Delivery :


Thickness Gauge Unit
4Nos. Calibration Foils
2 Calibration Plates (Zero Plate) 1 Iron & 1 Aluminium
1 Year Warranty
AAA Alkanline Battery
User Manual
Calibration Certificate


 

Conical Mandrel Bend Tester

Approx Price: Rs 9,800 / Piece 
Conical Mandrel Bend TesterConical Mandrel Bend Tester

The conical mandrel bend tester is used to determine properties of a coating. Resistance to cracking detachment from its substrate and its elongation during the test. Conical mandrel test is also known as standard method for assessing the flexibility and the adhesion properties of coatings when these are subjected to bending stresses This is accomplished by bending the test material around a conically shaped metal bar. The conical mandrel bending test is a commonly used for testing for painted or coated panels.

Conical Mandrel Bend Tester is widely recommended to test the resistance of a paint, coating, varnish to evaluate cracking or detachment from a metal panel. It is suitable for use with metal panels up to 0.8mm thick (flexible substrates up to 5mm thickness) e.g. polythenes or synthetic rubber. The apparatus consists of a steel mandrel 203mm in length and tapering from 38mm to 3mm in diameter. It will accommodate test panels up to 19cm x 11cm in size. A graduated scale on the clamping bar indicates the mandrel diameter at which failure has occurred. When this diameter is added to the thickness of the panel used, the percentage elongation can be calculated. Conical mandrel detects common failures of coating shows cracking or flaking after bending. Can be used in accordance with DIN ISO EN 6860, ASTM D 522, BS 3900 E11, DIN 53150



The conical mandrel bend tester is used to determine properties of a coating. Resistance to cracking detachment from its substrate and its elongation during the test. Conical mandrel test is also known as standard method for assessing the flexibility and the adhesion properties of coatings when these are subjected to bending stresses This is accomplished by bending the test material around a conically shaped metal bar. The conical mandrel bending test is a commonly used for testing for painted or coated panels.

Conical Mandrel Bend Tester is widely recommended to test the resistance of a paint, coating, varnish to evaluate cracking or detachment from a metal panel. It is suitable for use with metal panels up to 0.8mm thick (flexible substrates up to 5mm thickness) e.g. polythenes or synthetic rubber. The apparatus consists of a steel mandrel 203mm in length and tapering from 38mm to 3mm in diameter. It will accommodate test panels up to 19cm x 11cm in size. A graduated scale on the clamping bar indicates the mandrel diameter at which failure has occurred. When this diameter is added to the thickness of the panel used, the percentage elongation can be calculated. Conical mandrel detects common failures of coating shows cracking or flaking after bending. Can be used in accordance with DIN ISO EN 6860, ASTM D 522, BS 3900 E11, DIN 53150

Coating Thickness Gauge - Pencil Type

Approx Price: Rs 3,850 / Piece 

Coating Thickness Gauge - Pencil Type

Item Code: Coattest

Pull-Off Type with Cursor. (For Vertical use only.)
Confirming to accuracy as recommended in SSPC-PA 2-73T, ISO 2178-1982 (E),ASTM B 499-87 and ASTM D 1186-87.

Measures the thickness of Non-magnetic coating on magnetic base.
The coating may be of materials like:

as Plating : Gold, Copper, Zinc, Tin, Chromium, Hard Chromium, Lead etc.

as Coating: Paint, Resineous coating.

as Lining: Resin, Rubber, Fibre Glass.

as Film: Plastic, Metal foils.

Parkerising, Metalizing, Insulation coating.


The magnetic base may be of materials like;

Iron, Nickel, Cobalt, Magnetic Stainless Steel etc.


Available in

Range : 0 – 250 microns

Range : 50 – 800 microns

r />

Minitest 4100 Elektrophysik Coating Thickness Gauge

Approx Price: Rs 1.98 Lakh / Piece 

Application

Non-destructive measurement of:

  • non-magnetic coatings, e.g. paint and zinc on ferrous substrates
  • insulating coatings, e.g. paint and anodizing coatings on non-ferrous metals
  • non-ferrous metal coatings on insulating substrates

 

Performance features

  • wide range of wear-resistant probes which can be adapted to different applications
  • universal probe for measurements on steel and non-ferrous metals
  • high measuring accuracy and reproducibility
  • storage and evaluation of measuring values

Models

  • MiniTest 4100

    Memory structure to be defined freely for users with many different applications
    Statistical evaluation from various groups

  • MiniTest 3100
    Memory structure to be defined variously for users with few applications
    Statistical evaluation from various groups
  • MiniTest 2100
    Storage of measuring values for users with one application
    Statistical evaluation
  • MiniTest 1100
    For simple spot check measurements

 

Measuring principle

Magnetic induction and eddy current principle

Press O Film Testex Tapes

Approx Price: Rs 2,850 / Piece 
Minimum Order Quantity: 1 Piece
Offering Press O Film Testex Tapes USA:

Testex Tape is popularly called as Press-O-Film. Press-O-Film provides surface profile of a basted cleaned surface. It can produce virtually exact replicas of the blasted surface profile, which can be measured, using a snap gauge. Testex tapes offers a simple and very accurate method of measuring blasted profiles

Testex Tape / Press O Film consists of layer of crushable plastic microfoam coated onto a polyster film of highly uniform thickness.

Testex Tape Press-O-Film
R1001Coarse (range 20 to 51µm)
R1002X Coarse (range 38 to 114 µm)
R3003X Coarse Plus (range above 114µm)
R3004Paint Grade (range 32 to 85 µm)


Accessories
R1004Testex Snap Gauge (1/2 µm resolution)
R2001Testex Kit

Ford Cup - Viscosity Measuring Cup Aluminum

Approx Price: Rs 5,152 / Piece 

Ford viscosity cup is a simple gravity device that permits the timed flow of a known volume of liquid passing through an orifice located at the bottom.

Under ideal conditions, this rate of flow would be proportional to the kinematic viscosity (expressed in stokes and centistokes) that is dependent upon the specific gravity of the draining liquid.However, the conditions in a simple flow cup are seldom ideal for making true measurements of viscosity.

It is important when using a Ford Cup and when retesting liquids that the temperature of the cup and the liquid is maintained, as ambient temperature makes a significant difference to viscosity and thus flow rate.

These new Ford viscosity cups are extremely easy to use. Simply pour your sample into the cup and measure the time it takes for the liquid to flow through the orifice until the first break in the liquid stream. Use the included table to convert the elapsed time to centistokes (cSt).

The cups are made from solid Aluminium; the orifice is made from SS All the cups are calibrated to NIST-traceable oils.
An accessory kit, a stand, and a stand with water bath ports are sold separately.

 

Flow Cup Viscometer - Ford Cup

Approx Price: Rs 5,152 / Piece 
We are involved in production and supply of flow Cup Viscometer(Ford Cup). This is an appliance to ascertain the viscosity levels of fluids like water, grease, oil and others. To measure the viscosity level of liquids like lubricants, high capacity viscometers also known as rhemoters are used. Our viscometers are extensively used in Paints, chemicals, lubrication and other liquid processes.

Specifications:

  • Flow Cup Viscometer with stand (ford cup) b-4 made of brass
  • Flow Cup Viscometer with stand (ford cup) b-2, b-3, b-5, b-6, b-7, b-8,
  • Spare cup for above
  • Flow Cup Viscometer (ford cup) b-4, made of brass with certificate
  • Zahn Viscometer cup no.1, 2, 3, 4 & 5 with handle

Impact Tester

Approx Price: Rs 12,800 / Piece 

Impact Tester

tubular impact tester measures both the failure points.

most suitable for paints, varnishes, plastic coatings, laminations and sheet material.

sample clamp securely holds the test piece, impact can be varied by adjusting weights or heights.

  • aluminum tube marked in inches or centimeters
  • standard tube lengths are 25" and 40"
  • different weight 2 lb, 4 lb, 6 lb.

complies with astmd 2794 & is standards

Rubert Surface Roughness Comparison Chart

Approx Price: Rs 3,520 / Piece 
This set consists of 30 comparison specimens, covering six commonly-used machining methods (6 turned, 6 end-milled, 6 horizontally milled, 6 surface-ground, 3 lapped, 3 reamed/drilled. A label gives the ra values of each specimen in both metric and imperial units

Pencil Hardness Tester

Approx Price: Rs 9,800 / Piece 

Pencil Hardness Tester


  • The purpose of pencil scratch hardness tests is to determine the resistance of coating materials to scratch effects on surfaces.
  • In the wolff- wilbon test, pencils of various degrees of hardness are moved over the surface under a fixed pressure and angle to the surface. The degree of hardness of the pencil which damages the surface is taken as a measurement of scratch hardness e. g. “3H” hardness.
  • Instrument is supplied with set of hardness pencil, pencil sharpener, abrasive paper, operation manual, carrying case.
  • This test complies with ASTM D3363, is 101
Looking for Paint & Surface Testing Insturmenst ?
© Bombay Tools Center Bombay Pvt Ltd
 
Desktop Site Back to top