Surface Roughness Tester

Digital Surface Profile Gauge

Approx Price: Rs 15,000 / Piece 
Digital Surface Profile Guage
Measuring Range : 0-1000 Microns
Least Count : 0.001mm (1 Micron)
Accuracy : +/- 4 Microns / 4% of the Reading.
For Checking Sand Blasting, Shot Blasting, Grit Blasting

Additional Information:
  • Item Code: Dig-Surface-Profile-Gauge

Surface Roughness Tester

Approx Price: Rs 52,520 / Piece 

We are engaged in manufacturing a comprehensive range of surface roughness tester that is acknowledged for its features like accuracy in measurement and durability. These pocket-size & economically priced equipment is manufactured utilizing high grade raw material, to make these in compliance with ISO and DIN standards. Our range is used for measuring a varied range that is suitable for most material, especially flat, outer cylinder and sloping surface material. This tester Feature external calibration at keyboard with both Ra and Rz parameters in one instrument. Available with rechargeable batteries and can work while charging, these are available in competitive prices.


Technical Specifications :

Roughness ParametersRa, Rz, RY, Rq, Rt, Rp, Rmax, Rv, R3z, RS, RSk, Rmr Primary profile
Assessed profilesRoughness profile ® Rmr curve (material ration Mr.
Profile recording magnificationVv: 200x - 20000x Vh: 20x, 50x, 200x
Measuring systemMetric imperial
Display resolution0.001 µ m / 0.04 µ inch
DisplayLCD 128 x 64 dot - matrix, with Back light
Dimensions of LCD50 x 30 mm screen Pickup stylus position indicator Battery level indicator
Display FeaturesDirect display of parameters and profile Direct printing LCD brightness adjustment Auto-off after 5 minutes with auto - store Calibration through software
Data outputRS 232, direct to printer TA 220S or PC
RangeRa, Rq: 0.01-40 µ m Rz, Ry, Rp, Rt, R3z: 0.02 - 160 µ m Rsm, RS: 2-400 µ m Rmr: 1-100%
Cut off length0.25 mm / 0.8 mm / 2.5 mm
Evaluation length(1-5 cut-off (selectable)
Tracing length(1-5 cut-off) + 2 cut - off
Digital filterRC, PC-RC Gauss D-P
Pick-upStandard model TS 100, indicative, Diamond tip radius 5 µ m
Bores form diameter6.0 mm, depth 15 mm (TS 100)

Mitutoyo Surface Roughness Tester Surftest

Approx Price: Rs 98,000 / Piece 
Surftest SJ-201 Series 178-Portable Surface Roughness Tester

  • The display unit demonstrates IP53 protection level and is resistant to dripping water and dust.
  • The built-in battery, if fully charged, allows approximately 500 measurements to be made.
  • A convenient carrying case is supplied as standard for protecting the instrument in the field.
  • Up to 10 measurement results can be saved in the built-in memory.
  • Measurement results appear in large characters on the large LCD screen. Results can be confirmed at a glance.
  • Detailed set-ups, such as change of standards and cutoff lengths, can be made by pressing the relevant buttons after sliding back the top cover.
  • The SPC connector for Digimatic output and the RS-232C output connector are provided on the rear panel of the display unit for data output to external devices.
  • Printout of recorded profiles is also possible if the tester is connected to the dedicated hand-held, built-in battery operated compact SJ-printer (optional).


Customization: Desired parameters can be selected for calculation and display.GO/NG judgment:

Upper / lower limit setting: 2 parameters
Measurement conditions saving: Saves the conditions when the power is turned off.

Data saving: A maximum of 10 measurement results can be saved.

Calibration: Auto-calibration with the entry of numerical value.

Power saving function: If the auto-power-off function is ON then power turns off if no operation for 30 seconds.
AC adapter:526688A
Battery pack:12BAA240

C9 Casting Micro Finish Surface Comparator

Approx Price: Rs 12,850 / Piece 

C9 Casting Micro Finish Surface Comparator

Place the Micro Finish Comparator Surface Roughness Scale alongside your work piece. Slide the scale so that the rectangle with the surface roughness you want is adjacent to the piece you are examining. Compare by drawing the tip of the fingernail across each surface at right angles to the tool mark. The feel of the fingernail contact must be the same if the finishes are identical.

The original masters and the electro formed replica production masters have been checked at evenly distributed intervals. Sufficient measurements were taken to determine a representative average. The rating listed is the average of these readings.


The C-9 Cast Micro Finish Comparator Surface Roughness Scale is made by a dual electro forming process wherein nickel is electro deposited to provide an exact reproduction in intricate detail.


The same electroforming process used to produce the Surface Roughness Scale is available from GAR Electroforming to serve your product needs.


The C-9 Cast MICROFINISH COMPARATOR Surface Roughness Scale provides industry with established flat surface roughness specimens for visual and tactual comparison. It is used in specifying and controlling surface roughness when a product having the appearance of typically cast surfaces is required.



The C-9 Cast Microfinish Comparator Surface Roughness Scale provides an economical tool which permits roughness to be specified on the same basis as linear measurements. The surfaces presented are the result of years of research and engineering. Details covering this subject are now published in The American National Standards Institute (ANSI) specification titled: "Surface Texture, Surface Roughness, Waviness and Lay." ANSI/ASME B46.1

Looking for Surface Roughness Tester ?
© Bombay Tools Center Bombay Pvt Ltd
Desktop Site Back to top